![]() If reso is lower than batter, tune up reso head to match batter. If reso is higher pitch than batter, tune up batter to match reso head.Flip drum, place it on the towel, and tap the edge of the reso head.Glance at the fridge packed with favorite beverage.Flip drum over and repeat for batter side.Once every node is equal, there will no longer be any harmonic fluctuation/pulsing.Identify the low or high node and correct it by adjusting the tuning rod.As the two tones gradually approach unison, the pulsing slows down and may become so slow as to be imperceptible. The volume varies like in a tremolo as the sounds alternately interfere constructively and destructively. Tuning two tones to a unison will present a peculiar effect: when the two tones are close in pitch but not identical, the difference in frequency generates a pulsing. Place your head close to the drum and listen for the harmonic beats. And, like tuning a guitar using harmonics and octaves between strings, listen for the harmonic fluctuation that's caused by closely pitched nodes. At this point, higher-pitched harmonics can be heard when tapping the head.Adjust at each rod until pitch is similar. Once the tone from each lug is similar, tighten 1/2 or 1 full turn. ![]() Tighten the lower nodes until all nodes sound the same. Tap head with stick or finger, 1" from each tuning rod.Always use the star-pattern around the drum, never around the circumference. Using a tuning key, lightly turn it such that the tension feels the same amongst the rods.Place drum, reso side up, on folded towel, which is on a table.Finger tighten tuning rods all around (mine are lightly lubricated with light motor oil).I'm not sure what is meant by "Call To Post" as an interval type.ĮDIT: Under NO circumstances should you or anyone use a cordless impact drill with a tuning bit attached to tune drums! Just saying'!! And a another tab for the toms/intervals table in the manual (yeah it was a long laborous process to manually enter the data, but I suppose I was bored LOL). I created a separate tab for frequency lookup based on fundamental note. I've been having luck muffling the bottom head, either by setting the drum on carpeted flooring (on the head not being tuned), or by reaching down and pressing my finger (on the head not being tuned). Where "Fundamental" is the frequency associated with the fundamental note you're tuning to (you get the fundamental notes from the table in the Tune-bot manual, based on number of toms you have, and the kind of intervals you want). The first two rows have global variables for the lug constant, based on desired resonance: low, med, or high (I think these hold for ANY diameter drum): I created a spreadsheet to keep track of my tunings, with a separate tab for each kit I have: I am interested in what YOU are doing and your own technique, you own interpretation. I already read the complete instruction on the website, tried the calculator and looked at the various disappointing Youtubes videos. Is that right?įeel free If you want to share how you use your tune-bot. Even without a tune-bot, the note in the middle of the drum must be the final goal to achieve, right? In a sense that I need to reach the center note by ear, THEN equalize all the lugs, ignoring the note they produce, as long as they are equal and the note in the middle is equal to target. Then there is the note itself, let's say I want to tune my snare to an A, all the lugs have a note on the Tune-Bot but the center of the drum has a different note, If I equalize all the lugs starting from the one I prefer the most, the center WILL have a different note then all the equalized lugs at the end. Some people will put a finger on the top head, leave the head bellow unmuffled and get the readings. Some people will put a finger on the head bellow and get the readings by tapping the head on top. Do you damper 1 head or do it on a mount both heads free to resonate? (Whatever the tunebot instruction, I already read them) It's possible to tap a head when the bottom head is resting on a pillow but the reading are different from when both heads are free. I noticed that the wooden stick will often pitch much higher especially if the bottom head rests on a pillow. It's possible to test the heads with a mallet, a wooden stick or a something soft. I noticed the following things while doing my things. So yeah, the establishment of DW is pretty anti-Tune-Bot ? and I understand the point.īut since I spent 125CAD on mine and I believe it's a very nice sensor, I have some question for people who like the Tune-Bot.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |